You will need the Quick Roof Repair Tape # QR34FR. This particular roll is 25' long and 4" wide. It is one of the few products that will stick even to a wet surface. We also have it in a 6" wide Roll # QR44FR if you are wanting the wider size. view full answer...
Hey Mike, thanks for the pictures! Based on that what you need is the Premium RV Vinyl Insert Trim Molding # 37210015 that you referenced. view full answer...
Yes, you can use the ZIP System Green Roof Sheathing as an underlayment for the Alpha Systems Superflex TPO RV Roof Membrane # AL25CV.
Don't forget to also pick up the Alpha Systems RV Roof Replacement Installation Kit # AL63FJ as well since it comes with all of the parts needed to get the TPO properly installed on your RV! view full answer...
I wish we could help you Russell but we do not carry any RV flooring. As Grand Design and LaSalle Bristol cannot get you the parts you might check your local hardware store as they may have a very similar pattern vinyl that you would be able to use. You will most likely need to have a piece of your flooring to compare with their in stock or special order books to find the correct pattern. Since the patterns and colors are based on actual wood designs it may not be that hard to find. view full answer...
Hey David, we've used the LaSalle Bristol RV Roof Vent install kit part # 344270KITW to install several MaxxFan RV roof vents and it's worked well so it would also work well for you. This comes with everything needed so it would be a great choice. view full answer...
Hey Dock, the Furrion Chill HE RV Air Conditioner System # FR32PR that you referenced does come with everything needed to install in the roof vent hole you have currently on your Grand Design. You'd only need this part number and you'd have everything needed. view full answer...
Yes, the MaxxShade Retractable RV Roof Vent Shade part # MA00-03900 does have a vented strip section so it would be able to vent a little bit when it was closed. That's what the small holes you mentioned are for. view full answer...
While the same style AC used on an RV can be used on an enclosed car trailer you will need to work with the manufacturer to ensure the roof has the bracing needed to support the weight of the air conditioner since they weigh between 60-80lbs.
If your trailer manufacturer says your roof is braced for the weight you can look at installing either a 13.5K # ADV94FR or 15K # ADV64FR system. view full answer...
Hey Jeff!
We have the Roof Vent Installation Kit # 344270KITW which comes with 2 tubes of sealant, a roll of butyl tape, and screws to complete the installation. If you're just needing the tubes of sealant then you can find that as part # 34427034145-1.
I'm attaching a video where we use this installation kit for a roof vent so you can see our method for applying it. view full answer...
We don't have any EPDM roof membranes but you can go with a TPO membrane instead and you'll have a more energy efficient roof. We have several size options like the part # AL62CV which is 45 foot by 9-1/2 foot but if you need a different size I attached a link to a page that has all of the different options we carry. view full answer...
The Advent Air Replacement AC Unit part # ACCAR135 that you referenced is actually what you are looking for John! This is the correct BTU (13.5k), is white in color, and was designed specifically for replacing Carrier units like you have so it will be as easy of an install as possible. view full answer...
Yes, you can replace your GE air conditioner with the 15,000 Btu Furrion Chill HE RV Air Conditioner System # FR55PV.
This will be a complete replacement with no parts of your current AC used; no other parts are needed except for what comes with the # FR55PV. view full answer...
We don't make these parts, we just sell them, though I can tell you the 10-03817z is not something available. The best we can offer is a new vent like the MaxxAir Mini Manual RV Roof Vent # MA00-03700.
I have added a link below to our entire selection of roof vents. view full answer...
Hey Mike, thanks for reaching out!
The Replacement Printed Circuit Board for MaxxAir Powered Lift RV Roof Vents w/ Reversible Fan # MA10A21275K is the newer "10C21275K" C version you're wanting to get.
Our part numbers don't always match what the manufacturer lists out. I definitely get where the confusion comes into play, but part of the reason we have to do that is because of the wide variety of parts we carry. Sometimes different manufacturers have the same part number for different... view full answer...
Hey Mark/Larry,
We offer the Alpha Systems Superflex TPO roof membrane in almond at 9.5' wide x 30' long with part # AL28CV. If you need the installation kit with butyl tape, adhesive for the membrane, and sealant then I recommend going with the # AL47UV instead. view full answer...
The Replacement MaxxFan Plus 10-Speed Roof Vent with Smoke Lid # MA99FR is only compatible with the wall mount/remote (it says wall mount but can be used as a remote as well) Replacement Wall Control Panel for MaxxAir MaxxFan Plus Roof Vent # MA59FR.
So unfortunately it isn't compatible with the current remote you have. view full answer...
The only options we have Paul, are universal options like you already found. We have no way to see what parts Coachmen put on your Freelander 21QB or which one would fit best. You can easily measure your RV to see if the 84-1/2" # SP502L or 99-1/2" # LA-401 would be a better option. view full answer...
The AquaShed is great for wet climates but would likely wear quickly in intense Sun/UV so I'd recommend going with Adco's Olefin HD line instead. The Olefin HD line is designed for use in all climates and has a stronger more UV resistant roof panel to help protect your trailer. I recommend measuring the body of your Geo Pro to make sure that you're getting the correct length cover as well. For 18' to 20' you'll need part # AD97ZR and for 20' to 22' # AD47ZR. view full answer...